Wholesale White Sexy Bodycon Dress for Club
There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. A Wholesale White Sexy Bodycon Dress for Club reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together.
Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. For bandage knit or heavy ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.
Structure and seams
The build follows the same order on every size. These are the steps where the shape is won or lost. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide.
If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. The neckline is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel.
What goes on the spec sheet
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | white |
| Lining | bodice lined, skirt lined |
| Closure | concealed side zip |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 100 pcs per colour |
Where this style fails in production
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Cloth with insufficient recovery, so the dress grows through the day.
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.
What we can change for you
- Bonded or sewn finish at the neckline and armhole.
- Panel count from four to eight, with a small cost difference per unit.
- Neckline: square, sweetheart, halter or asymmetric.
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
