Wholesale Emerald Green Satin Bodycon Dress
A Wholesale Emerald Green Satin Bodycon Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Written down, the request is wholesale emerald green satin bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. Most of the money in a Wholesale Emerald Green Satin Bodycon Dress sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing.
Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. We start with satin on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.
Construction notes
The build follows the same order on every size. These are the steps where the shape is won or lost. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet.
When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
Spec sheet, line by line
| Shell | satin, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | green |
| Lining | fully lined, bagged hem |
| Closure | concealed side zip |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 50 pcs sample order |
The places this usually goes wrong
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
Customisation that does not break the price
- Bonded or sewn finish at the neckline and armhole.
- Panel count from four to eight, with a small cost difference per unit.
- Neckline: square, sweetheart, halter or asymmetric.
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.
If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
