Welcome to Bafinasa official website!

Wholesale Chocolate Brown Strapless Bodycon Dress for Club

Source:News / Time:2026-11-14

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.

Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. For bandage knit or heavy ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.

If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign.

Spec sheet, line by line

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybrown
Liningunlined with faced seams
Closurecovered button placket
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ100 pcs per colour

Failure points worth designing out

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

Customisation that does not break the price

  • Neckline: square, sweetheart, halter or asymmetric.
  • Bonded or sewn finish at the neckline and armhole.
  • Private label: woven label, care label and hangtag to your artwork.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top