Wholesale Emerald Green Maxi Bodycon Dress
Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Written down, the request is wholesale emerald green maxi bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back.
The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.
Construction notes
The build follows the same order on every size. These are the steps where the shape is won or lost. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.
Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.
On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. Shoulder and neckline decide whether a Wholesale Emerald Green Maxi Bodycon Dress looks expensive. Both are set by the block, not by the sewing. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.
Specification, item by item
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | maxi |
| Colourway | green |
| Lining | half lined to the hip |
| Closure | covered button placket |
| Size run | 34-44 with a regional grade |
| Sample lead time | 15-20 days with handwork |
| MOQ | 300 pcs per style |
Where this style fails in production
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Cloth with insufficient recovery, so the dress grows through the day.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.
Options on the table
- Panel count from four to eight, with a small cost difference per unit.
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.
If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.