Wholesale Emerald Green Sequin Bodycon Dress
We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. A Wholesale Emerald Green Sequin Bodycon Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. A Wholesale Emerald Green Sequin Bodycon Dress reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together.
Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.
Structure and seams
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.
Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.
Specification, item by item
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | green |
| Lining | unlined with faced seams |
| Closure | invisible centre-back zip |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 100 pcs per colour |
Where this style fails in production
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Cloth with insufficient recovery, so the dress grows through the day.
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. In bulk the failures cluster: skipped stitches on the side panel, shading between panels, and hems that go wavy after pressing. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.
What we can change for you
- Panel count from four to eight, with a small cost difference per unit.
- Bonded or sewn finish at the neckline and armhole.
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Neckline: square, sweetheart, halter or asymmetric.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Private label: woven label, care label and hangtag to your artwork.
Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.