Welcome to Bafinasa official website!

Wholesale Emerald Green Sexy Bodycon Dress for Club

Source:News / Time:2026-11-14

A Wholesale Emerald Green Sexy Bodycon Dress for Club can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. A Wholesale Emerald Green Sexy Bodycon Dress for Club reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves.

The neckline is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

What goes on the spec sheet

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Liningunlined with faced seams
Closurecovered button placket
Size run34-44 with a regional grade
Sample lead time15-20 days with handwork
MOQ150 pcs per style

Where this style fails in production

  • Cloth with insufficient recovery, so the dress grows through the day.
  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.

What we can change for you

  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Panel count from four to eight, with a small cost difference per unit.
  • Private label: woven label, care label and hangtag to your artwork.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top