Wholesale White High Slit Bodycon Dress
The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.
Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. For bandage knit or heavy ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. We start with bandage knit or heavy ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.
How it is built
Most of the handwork sits in a handful of steps, and each one has a right order. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet.
We keep the neckline as its own pattern piece so it can be changed without re-cutting the body. Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
The sheet we need before costing
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | white |
| Lining | bodice lined, skirt lined |
| Closure | covered button placket |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 150 pcs per style |
Failure points worth designing out
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.
What we can change for you
- Neckline: square, sweetheart, halter or asymmetric.
- Panel count from four to eight, with a small cost difference per unit.
- Bonded or sewn finish at the neckline and armhole.
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.