Welcome to Bafinasa official website!

Wholesale White Tight Bodycon Dress

Source:News / Time:2026-11-14

It helps to separate what the customer sees from what the factory feels. The outside is bandage knit or heavy ponte in white, the inside is structure, and the two have to agree on the same sample. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide.

The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

Specification, item by item

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaywhite
Liningfully lined, bagged hem
Closureinvisible centre-back zip
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ100 pcs per colour

Where this style fails in production

  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Customisation that does not break the price

  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Bonded or sewn finish at the neckline and armhole.
  • Panel count from four to eight, with a small cost difference per unit.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top