Wholesale White Tight Bodycon Dress for Club
Most of the money in a Wholesale White Tight Bodycon Dress for Club sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing. Written down, the request is wholesale white tight bodycon dress for club: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.
Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet.
How it is built
Most of the handwork sits in a handful of steps, and each one has a right order. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide.
The neckline is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. Shoulder and neckline decide whether a Wholesale White Tight Bodycon Dress for Club looks expensive. Both are set by the block, not by the sewing. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.
Spec sheet, line by line
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | white |
| Lining | half lined to the hip |
| Closure | stretch panel, no zip |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 50 pcs sample order |
What to check before bulk
- Cloth with insufficient recovery, so the dress grows through the day.
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.
Options on the table
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Bonded or sewn finish at the neckline and armhole.
- Panel count from four to eight, with a small cost difference per unit.
- Neckline: square, sweetheart, halter or asymmetric.
- Private label: woven label, care label and hangtag to your artwork.
- Private label: woven label, care label and hangtag to your artwork.
Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.