Welcome to Bafinasa official website!

Wholesale Emerald Green Sequin Bodycon Dress for Club

Source:News / Time:2026-11-14

A Wholesale Emerald Green Sequin Bodycon Dress for Club reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.

We start with bandage knit or heavy ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. For bandage knit or heavy ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.

We keep the neckline as its own pattern piece so it can be changed without re-cutting the body. The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates.

What goes on the spec sheet

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Liningunlined with faced seams
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ100 pcs per colour

The places this usually goes wrong

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Customisation that does not break the price

  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Private label: woven label, care label and hangtag to your artwork.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top