Welcome to Bafinasa official website!

Wholesale Chocolate Brown Velvet Bodycon Dress for Club

Source:News / Time:2026-11-14

Written down, the request is wholesale chocolate brown velvet bodycon dress for club: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

Construction notes

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.

Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Specification, item by item

Shellvelvet, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybrown
Liningfully lined, bagged hem
Closureinvisible centre-back zip
Size runS-3XL graded to your sheet
Sample lead time10-14 days on stock cloth
MOQ150 pcs per style

What to check before bulk

  • Cloth with insufficient recovery, so the dress grows through the day.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. In bulk the failures cluster: skipped stitches on the side panel, shading between panels, and hems that go wavy after pressing. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

What we can change for you

  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Panel count from four to eight, with a small cost difference per unit.
  • Private label: woven label, care label and hangtag to your artwork.
  • Private label: woven label, care label and hangtag to your artwork.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top