Welcome to Bafinasa official website!

Wholesale Red Bandage Bodycon Dress for Club

Source:News / Time:2026-11-14

Written down, the request is wholesale red bandage bodycon dress for club: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet.

We keep the neckline as its own pattern piece so it can be changed without re-cutting the body. If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Spec sheet, line by line

Shellbandage, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayred
Liningunlined with faced seams
Closurecovered button placket
Size runS-XL (4 sizes) for the test
Sample lead time10-14 days on stock cloth
MOQ300 pcs per style

What to check before bulk

  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

What we can change for you

  • Bonded or sewn finish at the neckline and armhole.
  • Panel count from four to eight, with a small cost difference per unit.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Private label: woven label, care label and hangtag to your artwork.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top