Welcome to Bafinasa official website!

Wholesale Red Cutout Bodycon Dress

Source:News / Time:2026-11-14

A Wholesale Red Cutout Bodycon Dress reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. A Wholesale Red Cutout Bodycon Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. We start with bandage knit or heavy ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves.

The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. The neckline is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

Specification, item by item

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayred
Lininghalf lined to the hip
Closurecovered button placket
Size runXS-2XL plus a curve block
Sample lead time10-14 days on stock cloth
MOQ300 pcs per style

What to check before bulk

  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

What we can change for you

  • Neckline: square, sweetheart, halter or asymmetric.
  • Bonded or sewn finish at the neckline and armhole.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top