Welcome to Bafinasa official website!

Wholesale Red Sequin Bodycon Dress for Club

Source:News / Time:2026-11-14

A Wholesale Red Sequin Bodycon Dress for Club can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.

The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. We keep the neckline as its own pattern piece so it can be changed without re-cutting the body.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

The sheet we need before costing

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayred
Lininghalf lined to the hip
Closurestretch panel, no zip
Size run34-44 with a regional grade
Sample lead time10-14 days on stock cloth
MOQ300 pcs per style

Failure points worth designing out

  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

Customisation that does not break the price

  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top