Wholesale Emerald Green Maxi Bodycon Dress for Club
A Wholesale Emerald Green Maxi Bodycon Dress for Club reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. A Wholesale Emerald Green Maxi Bodycon Dress for Club can be made at almost any price. What changes is how long it keeps its line and how much of the making shows.
Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Request a shrink test on the actual dye lot. Half a percent across a maxi is visible to the customer and invisible on the sheet.
Where the shape comes from
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.
When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.
Shoulder and neckline decide whether a Wholesale Emerald Green Maxi Bodycon Dress for Club looks expensive. Both are set by the block, not by the sewing. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.
Spec sheet, line by line
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | maxi |
| Colourway | green |
| Lining | half lined to the hip |
| Closure | stretch panel, no zip |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 300 pcs per style |
Where this style fails in production
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- Cloth with insufficient recovery, so the dress grows through the day.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.
What we can change for you
- Neckline: square, sweetheart, halter or asymmetric.
- Bonded or sewn finish at the neckline and armhole.
- Private label: woven label, care label and hangtag to your artwork.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
Previous: Stylish Sexy Bodycon Dress