Welcome to Bafinasa official website!

Wholesale Black Maxi Bodycon Dress for Club

Source:News / Time:2026-11-14

Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Written down, the request is wholesale black maxi bodycon dress for club: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back.

We start with bandage knit or heavy ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. Request a shrink test on the actual dye lot. Half a percent across a maxi is visible to the customer and invisible on the sheet.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down.

Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. We keep the neckline as its own pattern piece so it can be changed without re-cutting the body.

Shoulder and neckline decide whether a Wholesale Black Maxi Bodycon Dress for Club looks expensive. Both are set by the block, not by the sewing. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

What goes on the spec sheet

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthmaxi
Colourwayblack
Lininghalf lined to the hip
Closureconcealed side zip
Size runS-XL (4 sizes) for the test
Sample lead time10-14 days on stock cloth
MOQ150 pcs per style

The places this usually goes wrong

  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Options on the table

  • Neckline: square, sweetheart, halter or asymmetric.
  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top