Welcome to Bafinasa official website!

Wholesale White Long Sleeve Bodycon Dress for Club

Source:News / Time:2026-11-14

Most of the money in a Wholesale White Long Sleeve Bodycon Dress for Club sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. Written down, the request is wholesale white long sleeve bodycon dress for club: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. A Wholesale White Long Sleeve Bodycon Dress for Club can be made at almost any price. What changes is how long it keeps its line and how much of the making shows.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.

We keep the long sleeve as its own pattern piece so it can be changed without re-cutting the body. If the long sleeve is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.

Specification, item by item

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaywhite
Liningfully lined, bagged hem
Closureinvisible centre-back zip
Size run34-44 with a regional grade
Sample lead time15-20 days with handwork
MOQ50 pcs sample order

Where this style fails in production

  • Cloth with insufficient recovery, so the dress grows through the day.
  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.

Changes we can make at sample stage

  • Neckline: square, sweetheart, halter or asymmetric.
  • Bonded or sewn finish at the neckline and armhole.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top