New Arrival High Slit Bodycon Dress
We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.
Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.
How it is built
Most of the handwork sits in a handful of steps, and each one has a right order. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.
The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. We keep the neckline as its own pattern piece so it can be changed without re-cutting the body.
Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
Specification, item by item
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | unlined with faced seams |
| Closure | invisible centre-back zip |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 300 pcs per style |
Failure points worth designing out
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- Cloth with insufficient recovery, so the dress grows through the day.
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.
What we can change for you
- Bonded or sewn finish at the neckline and armhole.
- Neckline: square, sweetheart, halter or asymmetric.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.