Tube Bodycon Dress Wholesale
Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. A Tube Bodycon Dress Wholesale can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Written down, the request is tube bodycon dress wholesale: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.
Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.
Where the shape comes from
Most of the handwork sits in a handful of steps, and each one has a right order. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.
When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. We keep the neckline as its own pattern piece so it can be changed without re-cutting the body.
We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign.
What goes on the spec sheet
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | fully lined, bagged hem |
| Closure | invisible centre-back zip |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 150 pcs per style |
Where this style fails in production
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.
Customisation that does not break the price
- Panel count from four to eight, with a small cost difference per unit.
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.