Club Bodycon Dress Wholesale
Written down, the request is club bodycon dress wholesale: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. A Club Bodycon Dress Wholesale can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.
The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.
Structure and seams
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet.
We keep the neckline as its own pattern piece so it can be changed without re-cutting the body. If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.
Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
The sheet we need before costing
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | unlined with faced seams |
| Closure | invisible centre-back zip |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 150 pcs per style |
What to check before bulk
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Cloth with insufficient recovery, so the dress grows through the day.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
In bulk the failures cluster: skipped stitches on the side panel, shading between panels, and hems that go wavy after pressing. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.
Options on the table
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Bonded or sewn finish at the neckline and armhole.
- Panel count from four to eight, with a small cost difference per unit.
- Neckline: square, sweetheart, halter or asymmetric.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
