Halter Neck Bodycon Dress Wholesale
It helps to separate what the customer sees from what the factory feels. The outside is bandage knit or heavy ponte, the inside is structure, and the two have to agree on the same sample. Most of the money in a Halter Neck Bodycon Dress Wholesale sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing. Written down, the request is halter neck bodycon dress wholesale: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel.
Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.
Where the shape comes from
The build follows the same order on every size. These are the steps where the shape is won or lost. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down.
Check the halter after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. When the brief names the halter, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
Shoulder and neckline decide whether a Halter Neck Bodycon Dress Wholesale looks expensive. Both are set by the block, not by the sewing. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.
Spec sheet, line by line
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | bodice lined, skirt lined |
| Closure | covered button placket |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 100 pcs per colour |
Where this style fails in production
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.
Options on the table
- Neckline: square, sweetheart, halter or asymmetric.
- Bonded or sewn finish at the neckline and armhole.
- Private label: woven label, care label and hangtag to your artwork.
- Private label: woven label, care label and hangtag to your artwork.
The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.
A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
