Sequin Bodycon Dress Wholesale
A Sequin Bodycon Dress Wholesale reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together. Written down, the request is sequin bodycon dress wholesale: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.
Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.
Construction notes
Most of the handwork sits in a handful of steps, and each one has a right order. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide.
We keep the neckline as its own pattern piece so it can be changed without re-cutting the body. The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.
If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign.
Specification, item by item
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | fully lined, bagged hem |
| Closure | covered button placket |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 15-20 days with handwork |
| MOQ | 50 pcs sample order |
Where this style fails in production
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- Cloth with insufficient recovery, so the dress grows through the day.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. In bulk the failures cluster: skipped stitches on the side panel, shading between panels, and hems that go wavy after pressing.
Options on the table
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Neckline: square, sweetheart, halter or asymmetric.
- Panel count from four to eight, with a small cost difference per unit.
- Bonded or sewn finish at the neckline and armhole.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
