Bandage Bodycon Dress Wholesale
Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Bandage Bodycon Dress Wholesale can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. It helps to separate what the customer sees from what the factory feels. The outside is bandage, the inside is structure, and the two have to agree on the same sample.
Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. For bandage, order five to eight percent extra. Cutting around a shade band costs more than the cloth.
Where the shape comes from
The build follows the same order on every size. These are the steps where the shape is won or lost. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.
The neckline is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.
The sheet we need before costing
| Shell | bandage, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | half lined to the hip |
| Closure | covered button placket |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 100 pcs per colour |
The places this usually goes wrong
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- Cloth with insufficient recovery, so the dress grows through the day.
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
Options on the table
- Bonded or sewn finish at the neckline and armhole.
- Neckline: square, sweetheart, halter or asymmetric.
- Private label: woven label, care label and hangtag to your artwork.
- Private label: woven label, care label and hangtag to your artwork.
Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
