Wholesale Emerald Green Women's Bodycon Dress
Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. Written down, the request is wholesale emerald green women's bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. It helps to separate what the customer sees from what the factory feels. The outside is bandage knit or heavy ponte in green, the inside is structure, and the two have to agree on the same sample.
Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.
How it is built
The build follows the same order on every size. These are the steps where the shape is won or lost. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down.
If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.
On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.
Spec sheet, line by line
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | green |
| Lining | fully lined, bagged hem |
| Closure | covered button placket |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 15-20 days with handwork |
| MOQ | 300 pcs per style |
Failure points worth designing out
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.
What we can change for you
- Neckline: square, sweetheart, halter or asymmetric.
- Panel count from four to eight, with a small cost difference per unit.
- Bonded or sewn finish at the neckline and armhole.
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
