Velvet Bodycon Dress Wholesale

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. It helps to separate what the customer sees from what the factory feels. The outside is velvet, the inside is structure, and the two have to agree on the same sample. Most of the money in a Velvet Bodycon Dress Wholesale sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing. Written down, the request is velvet bodycon dress wholesale: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

Where the shape comes from

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.

The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.

Spec sheet, line by line

What to check before bulk

• Cloth with insufficient recovery, so the dress grows through the day.
• Too few panels, so the garment pulls across the hip and the seam line distorts.
• The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
• The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

In bulk the failures cluster: skipped stitches on the side panel, shading between panels, and hems that go wavy after pressing. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

Customisation that does not break the price

• Sleeve: sleeveless, cap, or long sleeve in the same cloth.
• Bonded or sewn finish at the neckline and armhole.
• Panel count from four to eight, with a small cost difference per unit.
• Neckline: square, sweetheart, halter or asymmetric.
• Private label: woven label, care label and hangtag to your artwork.
• Shell swap: the same block in a lighter or heavier cloth, priced separately.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.