Strapless Bodycon Dress Wholesale
Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. It helps to separate what the customer sees from what the factory feels. The outside is bandage knit or heavy ponte, the inside is structure, and the two have to agree on the same sample. Most of the money in a Strapless Bodycon Dress Wholesale sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing.
We start with bandage knit or heavy ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. For bandage knit or heavy ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.
Construction notes
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.
The neckline is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.
For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign.
The sheet we need before costing
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | unlined with faced seams |
| Closure | covered button placket |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 100 pcs per colour |
The places this usually goes wrong
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- Cloth with insufficient recovery, so the dress grows through the day.
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
Customisation that does not break the price
- Bonded or sewn finish at the neckline and armhole.
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Neckline: square, sweetheart, halter or asymmetric.
- Panel count from four to eight, with a small cost difference per unit.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Private label: woven label, care label and hangtag to your artwork.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
