Bodycon Dress Wholesale

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Written down, the request is bodycon dress wholesale: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.

Construction notes

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down.

Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

What goes on the spec sheet

What to check before bulk

• Too few panels, so the garment pulls across the hip and the seam line distorts.
• A fused hem used to control the edge, making it stiff and visibly different from the body.
• Cloth with insufficient recovery, so the dress grows through the day.
• The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
• The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.

Customisation that does not break the price

• Bonded or sewn finish at the neckline and armhole.
• Sleeve: sleeveless, cap, or long sleeve in the same cloth.
• Neckline: square, sweetheart, halter or asymmetric.
• Panel count from four to eight, with a small cost difference per unit.
• Shell swap: the same block in a lighter or heavier cloth, priced separately.
• Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.