Burgundy Long Sleeve Bodycon Dress
A Burgundy Long Sleeve Bodycon Dress reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Written down, the request is burgundy long sleeve bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.
Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. For bandage knit or heavy ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth.
Where the shape comes from
The build follows the same order on every size. These are the steps where the shape is won or lost. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.
If the long sleeve is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. We keep the long sleeve as its own pattern piece so it can be changed without re-cutting the body.
Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates.
What goes on the spec sheet
| Shell | a bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | burgundy |
| Lining | bodice lined, skirt lined |
| Closure | covered button placket |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 15-20 days with handwork |
| MOQ | 50 pcs sample order |
The places this usually goes wrong
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.
What we can change for you
- Panel count from four to eight, with a small cost difference per unit.
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
