Welcome to Bafinasa official website!

Women's Night Club Hot Pink Backless Bodycon Dress

Source:News / Time:2026-11-14

Written down, the request is women's night club hot pink backless bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. It helps to separate what the customer sees from what the factory feels. The outside is bandage knit or heavy ponte in pink, the inside is structure, and the two have to agree on the same sample.

Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves.

The backless reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. When the brief names the backless, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign.

Specification, item by item

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaypink
Liningfully lined, bagged hem
Closurecovered button placket
Size runS-XL (4 sizes) for the test
Sample lead time10-14 days on stock cloth
MOQ100 pcs per colour

What to check before bulk

  • Cloth with insufficient recovery, so the dress grows through the day.
  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. In bulk the failures cluster: skipped stitches on the side panel, shading between panels, and hems that go wavy after pressing. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

Changes we can make at sample stage

  • Neckline: square, sweetheart, halter or asymmetric.
  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Private label: woven label, care label and hangtag to your artwork.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top