Welcome to Bafinasa official website!

Red Cutout Bodycon Dress for Night Club

Source:News / Time:2026-11-14

This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. It helps to separate what the customer sees from what the factory feels. The outside is bandage knit or heavy ponte in red, the inside is structure, and the two have to agree on the same sample. A Red Cutout Bodycon Dress for Night Club reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together. Most of the money in a Red Cutout Bodycon Dress for Night Club sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

How it is built

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down.

When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. We keep the neckline as its own pattern piece so it can be changed without re-cutting the body.

On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

What goes on the spec sheet

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayred
Liningunlined with faced seams
Closureconcealed side zip
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ50 pcs sample order

What to check before bulk

  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.

Customisation that does not break the price

  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Private label: woven label, care label and hangtag to your artwork.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top