Welcome to Bafinasa official website!

Chocolate Brown Bodycon Dress for Night Club

Source:News / Time:2026-11-14

Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Most of the money in a Chocolate Brown Bodycon Dress for Night Club sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.

Construction notes

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide.

When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. The neckline is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign.

What goes on the spec sheet

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybrown
Liningbodice lined, skirt lined
Closureconcealed side zip
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ300 pcs per style

What to check before bulk

  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

What we can change for you

  • Bonded or sewn finish at the neckline and armhole.
  • Panel count from four to eight, with a small cost difference per unit.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top