Welcome to Bafinasa official website!

Emerald Green Backless Bodycon Dress for Night Club

Source:News / Time:2026-11-14

Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Emerald Green Backless Bodycon Dress for Night Club can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. It helps to separate what the customer sees from what the factory feels. The outside is bandage knit or heavy ponte in green, the inside is structure, and the two have to agree on the same sample.

Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

How it is built

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves.

Check the backless after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. We keep the backless as its own pattern piece so it can be changed without re-cutting the body.

On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.

Spec sheet, line by line

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Liningunlined with faced seams
Closurestretch panel, no zip
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ300 pcs per style

Failure points worth designing out

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

Changes we can make at sample stage

  • Neckline: square, sweetheart, halter or asymmetric.
  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Private label: woven label, care label and hangtag to your artwork.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top