Welcome to Bafinasa official website!

Night Club Hot Pink Long Sleeve Bodycon Dress

Source:News / Time:2026-11-14

Written down, the request is night club hot pink long sleeve bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. We start with bandage knit or heavy ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.

Structure and seams

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet.

The long sleeve reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. The long sleeve is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.

Spec sheet, line by line

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaypink
Liningfully lined, bagged hem
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ300 pcs per style

What to check before bulk

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

What we can change for you

  • Bonded or sewn finish at the neckline and armhole.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Panel count from four to eight, with a small cost difference per unit.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top