Welcome to Bafinasa official website!

Buy Sexy Emerald Green Sequin Bodycon Dress

Source:News / Time:2026-11-14

We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down.

When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. We keep the neckline as its own pattern piece so it can be changed without re-cutting the body.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign.

Specification, item by item

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Liningbodice lined, skirt lined
Closureinvisible centre-back zip
Size runS-3XL graded to your sheet
Sample lead time15-20 days with handwork
MOQ50 pcs sample order

Failure points worth designing out

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.

Changes we can make at sample stage

  • Panel count from four to eight, with a small cost difference per unit.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top