Welcome to Bafinasa official website!

Women's Night Club White Maxi Bodycon Dress

Source:News / Time:2026-11-14

Most of the money in a Women's Night Club White Maxi Bodycon Dress sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing. Written down, the request is women's night club white maxi bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet.

If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. We keep the neckline as its own pattern piece so it can be changed without re-cutting the body.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

What goes on the spec sheet

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthmaxi
Colourwaywhite
Liningunlined with faced seams
Closureconcealed side zip
Size run34-44 with a regional grade
Sample lead time15-20 days with handwork
MOQ300 pcs per style

The places this usually goes wrong

  • Cloth with insufficient recovery, so the dress grows through the day.
  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.

What we can change for you

  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Private label: woven label, care label and hangtag to your artwork.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top