Welcome to Bafinasa official website!

Night Club Nude High Slit Bodycon Dress

Source:News / Time:2026-11-14

A Night Club Nude High Slit Bodycon Dress reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together. Written down, the request is night club nude high slit bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. We start with bandage knit or heavy ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening.

Where the shape comes from

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.

We keep the neckline as its own pattern piece so it can be changed without re-cutting the body. Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

What goes on the spec sheet

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaynude
Liningunlined with faced seams
Closureinvisible centre-back zip
Size run34-44 with a regional grade
Sample lead time15-20 days with handwork
MOQ150 pcs per style

What to check before bulk

  • Cloth with insufficient recovery, so the dress grows through the day.
  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. In bulk the failures cluster: skipped stitches on the side panel, shading between panels, and hems that go wavy after pressing.

Options on the table

  • Bonded or sewn finish at the neckline and armhole.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Private label: woven label, care label and hangtag to your artwork.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top