Welcome to Bafinasa official website!

Women's High Slit Sequin Bodycon Dress

Source:News / Time:2026-11-14

Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. Written down, the request is women's high slit sequin bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Most of the money in a Women's High Slit Sequin Bodycon Dress sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

Where the shape comes from

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet.

If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Shoulder and neckline decide whether a Women's High Slit Sequin Bodycon Dress looks expensive. Both are set by the block, not by the sewing. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign.

The sheet we need before costing

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningfully lined, bagged hem
Closurecovered button placket
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ50 pcs sample order

What to check before bulk

  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

Changes we can make at sample stage

  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top