Welcome to Bafinasa official website!

Women's Side Slit Maxi Bodycon Dress

Source:News / Time:2026-11-14

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Written down, the request is women's side slit maxi bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.

If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. We keep the neckline as its own pattern piece so it can be changed without re-cutting the body.

On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Specification, item by item

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthmaxi
Colourwaybuyer colourway, lab-dipped under two lights
Liningunlined with faced seams
Closurecovered button placket
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ50 pcs sample order

What to check before bulk

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

What we can change for you

  • Neckline: square, sweetheart, halter or asymmetric.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Bonded or sewn finish at the neckline and armhole.
  • Panel count from four to eight, with a small cost difference per unit.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top