Welcome to Bafinasa official website!

Women's Open Back Club Bodycon Dress

Source:News / Time:2026-11-14

We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. A Women's Open Back Club Bodycon Dress reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together. A Women's Open Back Club Bodycon Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.

The neckline is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

Specification, item by item

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningunlined with faced seams
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time10-14 days on stock cloth
MOQ150 pcs per style

Where this style fails in production

  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.

Options on the table

  • Neckline: square, sweetheart, halter or asymmetric.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Bonded or sewn finish at the neckline and armhole.
  • Panel count from four to eight, with a small cost difference per unit.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top