Welcome to Bafinasa official website!

Chocolate Brown Satin Mini Bodycon Dress

Source:News / Time:2026-11-14

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Written down, the request is chocolate brown satin mini bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Request a shrink test on the actual dye lot. Half a percent across a mini is visible to the customer and invisible on the sheet. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.

Where the shape comes from

The build follows the same order on every size. These are the steps where the shape is won or lost. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down.

We keep the neckline as its own pattern piece so it can be changed without re-cutting the body. When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

Spec sheet, line by line

Shellsatin, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthmini
Colourwaybrown
Liningbodice lined, skirt lined
Closurestretch panel, no zip
Size run34-44 with a regional grade
Sample lead time12-18 days after spec sign-off
MOQ100 pcs per colour

What to check before bulk

  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.

What we can change for you

  • Bonded or sewn finish at the neckline and armhole.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Panel count from four to eight, with a small cost difference per unit.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top