Welcome to Bafinasa official website!

Burgundy Satin Bodycon Dress

Source:News / Time:2026-11-14

Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. A Burgundy Satin Bodycon Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Written down, the request is burgundy satin bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.

Structure and seams

Most of the handwork sits in a handful of steps, and each one has a right order. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet.

The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. We keep the neckline as its own pattern piece so it can be changed without re-cutting the body.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

Specification, item by item

Shellsatin, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayburgundy
Lininghalf lined to the hip
Closurestretch panel, no zip
Size runS-XL (4 sizes) for the test
Sample lead time10-14 days on stock cloth
MOQ300 pcs per style

Where this style fails in production

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

Customisation that does not break the price

  • Panel count from four to eight, with a small cost difference per unit.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Bonded or sewn finish at the neckline and armhole.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top