Welcome to Bafinasa official website!

White Velvet Tube Bodycon Dress

Source:News / Time:2026-11-14

Written down, the request is white velvet tube bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. It helps to separate what the customer sees from what the factory feels. The outside is velvet in white, the inside is structure, and the two have to agree on the same sample.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

Where the shape comes from

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.

Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign.

What goes on the spec sheet

Shellvelvet, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaywhite
Liningbodice lined, skirt lined
Closurecovered button placket
Size run34-44 with a regional grade
Sample lead time10-14 days on stock cloth
MOQ100 pcs per colour

Where this style fails in production

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.

Options on the table

  • Panel count from four to eight, with a small cost difference per unit.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Private label: woven label, care label and hangtag to your artwork.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top