Women's White Ribbed Knit High Slit Bodycon Dress
Most of the money in a Women's White Ribbed Knit High Slit Bodycon Dress sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing. It helps to separate what the customer sees from what the factory feels. The outside is knit in white, the inside is structure, and the two have to agree on the same sample. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.
Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. For knit, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening.
Construction notes
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet.
Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The neckline is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
Spec sheet, line by line
| Shell | knit, swatch-approved, one dye lot for bulk |
| Body | bodycon dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | white |
| Lining | unlined with faced seams |
| Closure | concealed side zip |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 100 pcs per colour |
The places this usually goes wrong
- A fused hem used to control the edge, making it stiff and visibly different from the body.
- Too few panels, so the garment pulls across the hip and the seam line distorts.
- A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.
Options on the table
- Panel count from four to eight, with a small cost difference per unit.
- Neckline: square, sweetheart, halter or asymmetric.
- Sleeve: sleeveless, cap, or long sleeve in the same cloth.
- Bonded or sewn finish at the neckline and armhole.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
