Welcome to Bafinasa official website!

Burgundy Mesh Cocktail Bodycon Dress

Source:News / Time:2026-11-14

It helps to separate what the customer sees from what the factory feels. The outside is mesh in burgundy, the inside is structure, and the two have to agree on the same sample. A Burgundy Mesh Cocktail Bodycon Dress reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together. Most of the money in a Burgundy Mesh Cocktail Bodycon Dress sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.

We keep the neckline as its own pattern piece so it can be changed without re-cutting the body. The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates.

The sheet we need before costing

Shellmesh, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayburgundy
Liningfully lined, bagged hem
Closurecovered button placket
Size runXS-2XL plus a curve block
Sample lead time10-14 days on stock cloth
MOQ150 pcs per style

The places this usually goes wrong

  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

Options on the table

  • Bonded or sewn finish at the neckline and armhole.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Panel count from four to eight, with a small cost difference per unit.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Private label: woven label, care label and hangtag to your artwork.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top