Welcome to Bafinasa official website!

Best Chocolate Brown Ribbed Knit Long Sleeve Bodycon Dress

Source:News / Time:2026-11-14

Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Best Chocolate Brown Ribbed Knit Long Sleeve Bodycon Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. It helps to separate what the customer sees from what the factory feels. The outside is knit in brown, the inside is structure, and the two have to agree on the same sample.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. We start with knit on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.

When the brief names the long sleeve, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. We keep the long sleeve as its own pattern piece so it can be changed without re-cutting the body.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

What goes on the spec sheet

Shellknit, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybrown
Liningfully lined, bagged hem
Closurecovered button placket
Size runXS-2XL plus a curve block
Sample lead time10-14 days on stock cloth
MOQ300 pcs per style

Where this style fails in production

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. In bulk the failures cluster: skipped stitches on the side panel, shading between panels, and hems that go wavy after pressing. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.

Changes we can make at sample stage

  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Private label: woven label, care label and hangtag to your artwork.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top