Welcome to Bafinasa official website!

Red Mesh High Slit Bodycon Dress

Source:News / Time:2026-11-14

It helps to separate what the customer sees from what the factory feels. The outside is mesh in red, the inside is structure, and the two have to agree on the same sample. A Red Mesh High Slit Bodycon Dress reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together. Most of the money in a Red Mesh High Slit Bodycon Dress sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves.

If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. The neckline is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

Specification, item by item

Shellmesh, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayred
Liningfully lined, bagged hem
Closurestretch panel, no zip
Size run34-44 with a regional grade
Sample lead time10-14 days on stock cloth
MOQ100 pcs per colour

Where this style fails in production

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

What we can change for you

  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Bonded or sewn finish at the neckline and armhole.
  • Panel count from four to eight, with a small cost difference per unit.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top