Welcome to Bafinasa official website!

White Mesh Cutout Bodycon Dress

Source:News / Time:2026-11-14

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Written down, the request is white mesh cutout bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

For mesh, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.

We keep the neckline as its own pattern piece so it can be changed without re-cutting the body. The neckline is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel.

Specification, item by item

Shellmesh, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaywhite
Liningfully lined, bagged hem
Closurestretch panel, no zip
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ100 pcs per colour

Where this style fails in production

  • Cloth with insufficient recovery, so the dress grows through the day.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Customisation that does not break the price

  • Neckline: square, sweetheart, halter or asymmetric.
  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Private label: woven label, care label and hangtag to your artwork.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top