Welcome to Bafinasa official website!

Red Mesh Cutout Bodycon Dress

Source:News / Time:2026-11-14

Written down, the request is red mesh cutout bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. For mesh, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet.

The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the side panel to move at different rates.

The sheet we need before costing

Shellmesh, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayred
Liningunlined with faced seams
Closureinvisible centre-back zip
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ50 pcs sample order

What to check before bulk

  • Cloth with insufficient recovery, so the dress grows through the day.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. In bulk the failures cluster: skipped stitches on the side panel, shading between panels, and hems that go wavy after pressing. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Options on the table

  • Panel count from four to eight, with a small cost difference per unit.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top