Welcome to Bafinasa official website!

Cheap Black Ribbed Knit Backless Bodycon Dress

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. A Cheap Black Ribbed Knit Backless Bodycon Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Written down, the request is cheap black ribbed knit backless bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet.

Structure and seams

Most of the handwork sits in a handful of steps, and each one has a right order. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.

The backless reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. The backless is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Shoulder and neckline decide whether a Cheap Black Ribbed Knit Backless Bodycon Dress looks expensive. Both are set by the block, not by the sewing. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign.

Specification, item by item

Shellknit, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayblack
Liningunlined with faced seams
Closurecovered button placket
Size run34-44 with a regional grade
Sample lead time15-20 days with handwork
MOQ150 pcs per style

What to check before bulk

  • Cloth with insufficient recovery, so the dress grows through the day.
  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.

Changes we can make at sample stage

  • Panel count from four to eight, with a small cost difference per unit.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Bonded or sewn finish at the neckline and armhole.
  • Private label: woven label, care label and hangtag to your artwork.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top