Welcome to Bafinasa official website!

Cheap Red Ribbed Knit Backless Bodycon Dress

Source:News / Time:2026-11-14

Most of the money in a Cheap Red Ribbed Knit Backless Bodycon Dress sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. It helps to separate what the customer sees from what the factory feels. The outside is knit in red, the inside is structure, and the two have to agree on the same sample. A Cheap Red Ribbed Knit Backless Bodycon Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows.

For knit, order five to eight percent extra. Cutting around a shade band costs more than the cloth. We start with knit on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves.

The backless reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. When the brief names the backless, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

Specification, item by item

Shellknit, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayred
Liningunlined with faced seams
Closurestretch panel, no zip
Size runS-XL (4 sizes) for the test
Sample lead time10-14 days on stock cloth
MOQ150 pcs per style

Where this style fails in production

  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.

What we can change for you

  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Bonded or sewn finish at the neckline and armhole.
  • Panel count from four to eight, with a small cost difference per unit.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Private label: woven label, care label and hangtag to your artwork.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top